Outils pour utilisateurs

Outils du site


livebox_thomson_bootlog

Différences

Ci-dessous, les différences entre deux révisions de la page.

Lien vers cette vue comparative

livebox_thomson_bootlog [2015/01/28 03:09] (Version actuelle)
Ligne 1: Ligne 1:
 +====== Bootlog Livebox Mini ======
  
 +<​code>​
 +HiZ>#
 +RESET
 +
 +Bus Pirate v3b
 +Firmware v5.10 (r559) ​ Bootloader v4.4
 +DEVID:​0x0447 REVID:​0x3046 (24FJ64GA002 B8)
 +http://​dangerousprototypes.com
 +HiZ>m
 +1. HiZ
 +2. 1-WIRE
 +3. UART
 +4. I2C
 +5. SPI
 +6. 2WIRE
 +7. 3WIRE
 +8. LCD
 +9. DIO
 +x. exit(without change)
 +
 +(1)>3
 +Set serial port speed: (bps)
 + 1. 300
 + 2. 1200
 + 3. 2400
 + 4. 4800
 + 5. 9600
 + 6. 19200
 + 7. 38400
 + 8. 57600
 + 9. 115200
 +10. BRG raw value
 +
 +(1)>9
 +Data bits and parity:
 + 1. 8, NONE *default ​
 + 2. 8, EVEN 
 + 3. 8, ODD 
 + 4. 9, NONE
 +(1)>
 +Stop bits:
 + 1. 1 *default
 + 2. 2
 +(1)>
 +Receive polarity:
 + 1. Idle 1 *default
 + 2. Idle 0
 +(1)>
 +Select output type:
 + 1. Open drain (H=Hi-Z, L=GND)
 + 2. Normal (H=3.3V, L=GND)
 +
 +(1)>
 +Ready
 +UART>(1)
 +UART bridge
 +Reset to exit
 +Are you sure? y
 +
 +
 +
 +DDR2 test...
 +VCDL test.
 +
 +Decompressing Bootloader................................
 +
 +Speedtouch initialization sequence started.
 +
 +
 +
 +Version BL: 1.3.7
 +Reading cpu info...........bcm96358 tp0 revision 1
 +MIPS is in Big endian mode 
 +Icache : 32Kb Icachelinesize : 16 bytes 
 +Dcache : 16Kb Dcachelinesize : 16 bytes 
 +BCM config reg CP0 : e30e1006 ​
 + Instruction cache enabled
 + Data cache enabled
 + Data cache is nonblocking
 +C0_CONFIG reg = 80008083
 + standard TLB config
 + Cacheable,​ write-back
 +
 +pfuncjmp = A0001840
 +Reading cpu info...........bcm96358 tp0 revision 1
 +MIPS is in Big endian mode 
 +Icache : 16Kb Icachelinesize : 16 bytes 
 +Dcache : 16Kb Dcachelinesize : 16 bytes 
 +BCM config reg CP0 : 230e1006 ​
 + Data cache is nonblocking
 +C0_CONFIG reg = 80008082
 + standard TLB config
 + Noncacheable
 +
 +
 +JTAG select tp0
 +BOOTING THE THOMSON LINUX KERNEL
 +
 +Starting the kernel @ 0x8037f000 ​
 +Linux version 2.6.12.6 (buildmgm@dslws-narenr) (gcc version 3.4.2) #1 Mon Jun 8 20:02:05 CST 2009
 +
 +C0 config : 2147516547x ​
 +
 +CPU revision is: 0002a010
 +
 +mpi: No Card is in the PCMCIA slot
 +
 +Determined physical RAM map:
 +
 + ​memory:​ 03ea0000 @ 00000000 (usable)
 +
 + ​memory:​ 00060000 @ 03ea0000 (reserved)
 +
 +On node 0 totalpages: 16032
 +
 +  DMA zone: 16032 pages, LIFO batch:7
 +
 +  Normal zone: 0 pages, LIFO batch:1
 +
 +  HighMem zone: 0 pages, LIFO batch:1
 +
 +Built 1 zonelists
 +
 +Kernel command line: maxcpus=1 bootaddr=0XBE720000
 +
 +livebox: the active partition is reported to be at BE720000
 +
 +Setting eDSP mode to Saturate and Shift
 +
 +brcm mips: enabling icache and dcache...
 +
 +Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
 +
 +Primary data cache 16kB, 2-way, linesize 16 bytes.
 +
 +Using board-specific TLB handlers
 +
 +PID hash table entries: 256 (order: 8, 4096 bytes)
 +
 +Using 150.000 MHz high precision timer.
 +
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +
 +Allocating memory for DSP module core and initialization code
 +
 +Allocated DSP module memory - CORE=0x8108a660 SIZE=900000,​ INIT=0x81166200 SIZE=5000
 +
 +Memory: 58424k/​64128k available (2804k kernel code, 5552k reserved, 707k data, 136k init, 0k highmem)
 +
 +Calibrating delay loop... (HZ=200) 299.00 BogoMIPS (lpj=747520)
 +
 +Mount-cache hash table entries: 512
 +
 +Checking for '​wait'​ instruction... ​ unavailable.
 +
 +NET: Registered protocol family 16
 +
 +SCSI subsystem initialized
 +
 +usbcore: registered new driver usbfs
 +
 +usbcore: registered new driver hub
 +
 +Bluetooth: Core ver 2.7
 +
 +NET: Registered protocol family 31
 +
 +Bluetooth: HCI device and connection manager initialized
 +
 +Bluetooth: HCI socket layer initialized
 +
 +squashfs: version 3.1 (2006/​08/​19) Phillip Lougher
 +
 +devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
 +
 +devfs: boot_options:​ 0x1
 +
 +JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
 +
 +Initializing Cryptographic API
 +
 +io scheduler noop registered
 +
 +RAMDISK driver initialized:​ 16 RAM disks of 4096K size 1024 blocksize
 +
 +PPP generic driver version 2.4.2
 +
 +NET: Registered protocol family 24
 +
 +livebox: initialize parser
 +
 +Inventel Blue5G Flash: Found 1 x16 devices at 0x0 in 16-bit bank
 +
 + ​Amd/​Fujitsu Extended Query Table at 0x0040
 +
 +Inventel Blue5G Flash: CFI does not contain boot bank location. Assuming top.
 +
 +number of CFI chips: 1
 +
 +cfi_cmdset_0002:​ Disabling erase-suspend-program due to code brokenness.
 +
 +RedBoot partition parsing not available
 +
 +parse_livebox_partitions
 +
 +livebox: user partition is created
 +
 +livebox: header of SYSTEM partition is detected
 +
 +livebox: kernel is at offset (be72001a), size (103483)
 +
 +livebox: rootfs is at offset (be824000), size (7c5000)
 +
 +livebox: info is at offset (befe9004), size (4) including a header of (4)
 +
 +livebox: (system_pattern) ds is at offset (befe9008), size (30)including a header of (4)
 +
 +livebox: SYSTEM partition is created
 +
 +livebox: no valid rescue partition detected. An empty one will be created.
 +
 +livebox mtd: rootfs (be824000, 7c5000), sdram(0)
 +
 +livebox mtd: user (be020000, 100000), sdram(0)
 +
 +livebox mtd: rescue (be120000, 600000), sdram(0)
 +
 +livebox mtd: lb_flash (be000000, 1000000), sdram(0)
 +
 +PT: creating a tree under /proc...
 +
 +   <​6>​[ lb_flash ]
 +
 +     <​6>​[ user ]
 +
 +     <​6>​[ system ]
 +
 +       <​6>​[ kernel ]
 +
 +       <​6>​[ rootfs ]
 +
 +       <​6>​[ info ]
 +
 +       <​6>​[ ds ]
 +
 +     <​6>​[ rescue ]
 +
 +PT: done.
 +
 +4 Livebox partitions found on MTD device Inventel Blue5G Flash
 +
 +Creating 4 MTD partitions on "​Inventel Blue5G Flash":​
 +
 +0x00824000-0x00fe9000 : "​rootfs"​
 +
 +0x00020000-0x00120000 : "​user"​
 +
 +0x00120000-0x00720000 : "​rescue"​
 +
 +0x00000000-0x01000000 : "​lb_flash"​
 +
 +PCI: Enabling device 0000:​00:​0a.0 (0000 -> 0002)
 +
 +PCI: Setting latency timer of device 0000:​00:​0a.0 to 64
 +
 +ehci_hcd 0000:​00:​0a.0:​ PCI device 14e4:6300 (Broadcom Corporation)
 +
 +ehci_hcd 0000:​00:​0a.0:​ new USB bus registered, assigned bus number 1
 +
 +ehci_hcd 0000:​00:​0a.0:​ irq 18, io mem 0xfffe1300
 +
 +PCI: cache line size of 32 is not supported by device 0000:​00:​0a.0
 +
 +ehci_hcd 0000:​00:​0a.0:​ park 0
 +
 +ehci_hcd 0000:​00:​0a.0:​ USB f.f initialized,​ EHCI 1.00, driver 10 Dec 2004
 +
 +hub 1-0:1.0: USB hub found
 +
 +hub 1-0:1.0: 2 ports detected
 +
 +ohci_hcd: 2004 Nov 08 USB 1.1 '​Open'​ Host Controller (OHCI) Driver (PCI)
 +
 +PCI: Enabling device 0000:​00:​09.0 (0000 -> 0002)
 +
 +PCI: Setting latency timer of device 0000:​00:​09.0 to 64
 +
 +ohci_hcd 0000:​00:​09.0:​ PCI device 14e4:6300 (Broadcom Corporation)
 +
 +ohci_hcd 0000:​00:​09.0:​ new USB bus registered, assigned bus number 2
 +
 +ohci_hcd 0000:​00:​09.0:​ irq 13, io mem 0xfffe1400
 +
 +hub 2-0:1.0: USB hub found
 +
 +hub 2-0:1.0: 2 ports detected
 +
 +usbcore: registered new driver usblp
 +
 +drivers/​usb/​class/​usblp.c:​ v0.13: USB Printer Device Class driver
 +
 +Initializing USB Mass Storage driver...
 +
 +usbcore: registered new driver usb-storage
 +
 +USB Mass Storage support registered.
 +
 +Livebox Button API has been initialized
 +
 +bcm963xx_serial driver v2.0
 +
 +u32 classifier
 +
 +    OLD policer on 
 +
 +NET: Registered protocol family 2
 +
 +IP: routing cache hash table of 512 buckets, 4Kbytes
 +
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +
 +TCP: Hash tables configured (established 2048 bind 2048)
 +
 +ip_conntrack version 2.1 (501 buckets, 4008 max) - 248 bytes per conntrack
 +
 +ip_conntrack_rtsp v0.1_Thomson Telecom Beijing loading
 +
 +ip_nat_rtsp v0.1_Thomson Telecom Beijing loading
 +
 +ip_tables: (C) 2000-2002 Netfilter core team
 +
 +NET: Registered protocol family 1
 +
 +NET: Registered protocol family 10
 +
 +IPv6 over IPv4 tunneling driver
 +
 +NET: Registered protocol family 17
 +
 +Bridge firewalling registered
 +
 +Ebtables v2.0 registered
 +
 +NET: Registered protocol family 8
 +
 +NET: Registered protocol family 20
 +
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +
 +VFS: Mounted root (squashfs filesystem) readonly.
 +
 +Mounted devfs on /dev
 +
 +Freeing unused kernel memory: 136k freed
 +
 +Algorithmics/​MIPS FPU Emulator v1.5
 +
 +
 +SYSINIT
 +
 +LIVEBOX version : 7.2.9.8
 +
 +Mounting proc filesystem ...
 +Mounting tmpfs filesystem (/var) ...
 +Mounting tmpfs filesystem (/tmp) ...
 +Mounting devpts filesystem (/dev/pts) ...
 +> NORMAL BOOT <
 +
 +
 +> BOOT SYSTEM <
 +
 +Mounting other filesystems ...
 +Switching to RUNLEVEL 1 ...
 +*********************** Starting script /​etc/​rc1.d/​S02hardware.adsl at: 6.04 0.92
 +Starting ADSL...
 +    atmapi.ko... atmapi: module license '​Proprietary'​ taints kernel.
 +
 +ok
 +    adsldd.ko... ok
 +    blaadd.ko... ok
 +*********************** Starting script /​etc/​rc1.d/​S03firewall at: 10.68 0.92
 +*********************** Starting script /​etc/​rc1.d/​S03nat at: 11.80 0.92
 +*********************** Starting script /​etc/​rc1.d/​S04adsl at: 12.50 0.92
 +adsl start ...
 +BcmAdsl_Initialize=0xC00D0998,​ g_pFnNotifyCallback=0xC00F2644
 +
 +AnnexCParam=0x00000000 AnnexAParam=0x00103187 adsl2=0x0000C001
 +
 +pSdramPHY=0xA3FFFFF8,​ 0xFFFBDFFE 0xDFADBFFF
 +
 +AdslCoreHwReset:​ AdslOemDataAddr = 0xA3FFC0E4
 +
 +AdslCoreEcUpdTmr:​ timeMs=-286715 ecUpdMask=0x40000
 +
 +AnnexCParam=0x00000000 AnnexAParam=0x00103187 adsl2=0x0000C001
 +
 +[BCM DSL DRIVER] TMM ModemOptions : 00:​00:​00:​00:​20:​04:​00:​00:​06:​00:​00:​00:​00:​00:​00
 +
 +
 +TmmBcmAdsl_SetModemOptions rc =0 !!
 +
 +TmmConfigure ADSL ext config rc =0 !!
 +
 +BcmAdsl_SetOemParameter 6, len=32 stat=32 ​  !!
 +
 +BcmAdsl_SetOemParameter 8, len=2 stat=2 ​  !!
 +
 +BcmAdsl_SetOemParameter 4, len=8 stat=8 ​  !!
 +
 +BcmAdsl_SetOemParameter 5, len=17 stat=17 ​  !!
 +
 +_MODEMLABEL (drv)= A2pBT010g2.d20h
 +
 +_ADSL_EOC_VERSION= ff81637.2.9.8
 +
 +*********************** Starting script /​etc/​rc1.d/​S05hardware at: 13.73 0.92
 +No Generic SPI support...
 +Starting Ethernet...
 +    bcm_enet.ko... Broadcom BCM6358A1 Ethernet Network Device v0.3 Jun  8 2009 19:52:09
 +
 +Config Internal PHY Through MDIO
 +
 +BCM63xx_ENET:​ 10 MB Half-Duplex (assumed)
 +
 +eth0: MAC Address: 00:​07:​3A:​FF:​FF:​FF
 +
 +Broadcom BCM6358A1 Ethernet Network Device v0.3 Jun  8 2009 19:52:09
 +
 +Config External PHY Through MDIO
 +
 +BCM63xx_ENET:​ 10 MB Half-Duplex (assumed)
 +
 +eth1: MAC Address: 00:​07:​3A:​FF:​FF:​FF
 +
 +ok
 +No USB support...
 +Starting ATH WLAN...
 +ath_hal: 0.9.14.25 (AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, DEBUG)
 +
 +ath_dfs: Version 2.0.0
 +
 +Copyright (c) 2005-2006 Atheros Communications,​ Inc. All Rights Reserved
 +
 +wlan: 0.8.4.2 (Atheros/​multi-bss)
 +
 +ath_rate_atheros:​ Version 2.0.1
 +
 +Copyright (c) 2001-2004 Atheros Communications,​ Inc, All Rights Reserved
 +
 +ath_pci: 0.9.4.5 (Atheros/​multi-bss)
 +
 +ath_pci: CR-LSDK-1.3.1.110
 +
 +PCI: Enabling device 0000:​00:​01.0 (0000 -> 0002)
 +
 +Chan 2412: MaxPow = 96 MinPow = 0
 +
 +Chan 2412: MaxPow = 92 MinPow = 0
 +
 +Chan 2417: MaxPow = 96 MinPow = 0
 +
 +Chan 2417: MaxPow = 92 MinPow = 0
 +
 +Chan 2422: MaxPow = 96 MinPow = 0
 +
 +Chan 2422: MaxPow = 92 MinPow = 0
 +
 +Chan 2427: MaxPow = 96 MinPow = 0
 +
 +Chan 2427: MaxPow = 92 MinPow = 0
 +
 +Chan 2432: MaxPow = 96 MinPow = 0
 +
 +Chan 2432: MaxPow = 92 MinPow = 0
 +
 +Chan 2437: MaxPow = 96 MinPow = 0
 +
 +Chan 2437: MaxPow = 92 MinPow = 0
 +
 +Chan 2442: MaxPow = 96 MinPow = 0
 +
 +Chan 2442: MaxPow = 92 MinPow = 0
 +
 +Chan 2447: MaxPow = 96 MinPow = 0
 +
 +Chan 2447: MaxPow = 92 MinPow = 0
 +
 +Chan 2452: MaxPow = 97 MinPow = 0
 +
 +Chan 2452: MaxPow = 93 MinPow = 0
 +
 +Chan 2457: MaxPow = 97 MinPow = 0
 +
 +Chan 2457: MaxPow = 93 MinPow = 0
 +
 +Chan 2462: MaxPow = 98 MinPow = 0
 +
 +Chan 2462: MaxPow = 94 MinPow = 0
 +
 +Chan 2467: MaxPow = 98 MinPow = 0
 +
 +Chan 2467: MaxPow = 94 MinPow = 0
 +
 +Chan 2472: MaxPow = 98 MinPow = 0
 +
 +Chan 2472: MaxPow = 94 MinPow = 0
 +
 +Chan 2412: MaxPow = 28 MinPow = 0
 +
 +Chan 2412: MaxPow = 28 MinPow = 0
 +
 +Chan 2417: MaxPow = 36 MinPow = 0
 +
 +Chan 2417: MaxPow = 36 MinPow = 0
 +
 +Chan 2422: MaxPow = 36 MinPow = 0
 +
 +Chan 2422: MaxPow = 36 MinPow = 0
 +
 +Chan 2427: MaxPow = 36 MinPow = 0
 +
 +Chan 2427: MaxPow = 36 MinPow = 0
 +
 +Chan 2432: MaxPow = 36 MinPow = 0
 +
 +Chan 2432: MaxPow = 36 MinPow = 0
 +
 +Chan 2437: MaxPow = 36 MinPow = 0
 +
 +Chan 2437: MaxPow = 36 MinPow = 0
 +
 +Chan 2442: MaxPow = 28 MinPow = 0
 +
 +Chan 2442: MaxPow = 28 MinPow = 0
 +
 +Chan 2447: MaxPow = 28 MinPow = 0
 +
 +Chan 2447: MaxPow = 28 MinPow = 0
 +
 +Chan 2452: MaxPow = 28 MinPow = 0
 +
 +Chan 2452: MaxPow = 28 MinPow = 0
 +
 +Chan 2457: MaxPow = 28 MinPow = 0
 +
 +Chan 2457: MaxPow = 28 MinPow = 0
 +
 +Chan 2462: MaxPow = 28 MinPow = 0
 +
 +Chan 2462: MaxPow = 28 MinPow = 0
 +
 +Chan 2467: MaxPow = 28 MinPow = 0
 +
 +Chan 2467: MaxPow = 28 MinPow = 0
 +
 +Chan 2472: MaxPow = 28 MinPow = 0
 +
 +Chan 2472: MaxPow = 28 MinPow = 0
 +
 +Chan  Freq  RegPwr ​ HT   CTL CTL_U CTL_L DFS
 +
 +   ​1 ​ 2412g     ​20 ​       0    0    0     N
 +
 +   ​1 ​ 2412b     ​20 ​       0    0    0     N
 +
 +   ​2 ​ 2417g     ​20 ​       0    0    0     N
 +
 +   ​2 ​ 2417b     ​20 ​       0    0    0     N
 +
 +   ​3 ​ 2422g     ​20 ​       0    0    0     N
 +
 +   ​3 ​ 2422b     ​20 ​       0    0    0     N
 +
 +   ​4 ​ 2427g     ​20 ​       0    0    0     N
 +
 +   ​4 ​ 2427b     ​20 ​       0    0    0     N
 +
 +   ​5 ​ 2432g     ​20 ​       0    0    0     N
 +
 +   ​5 ​ 2432b     ​20 ​       0    0    0     N
 +
 +   ​6 ​ 2437g     ​20 ​       0    0    0     N
 +
 +   ​6 ​ 2437b     ​20 ​       0    0    0     N
 +
 +   ​7 ​ 2442g     ​20 ​       0    0    0     N
 +
 +   ​7 ​ 2442b     ​20 ​       0    0    0     N
 +
 +   ​8 ​ 2447g     ​20 ​       0    0    0     N
 +
 +   ​8 ​ 2447b     ​20 ​       0    0    0     N
 +
 +   ​9 ​ 2452g     ​20 ​       0    0    0     N
 +
 +   ​9 ​ 2452b     ​20 ​       0    0    0     N
 +
 +  10  2457g     ​20 ​       0    0    0     N
 +
 +  10  2457b     ​20 ​       0    0    0     N
 +
 +  11  2462g     ​20 ​       0    0    0     N
 +
 +  11  2462b     ​20 ​       0    0    0     N
 +
 +  12  2467g     ​20 ​       0    0    0     N
 +
 +  12  2467b     ​20 ​       0    0    0     N
 +
 +  13  2472g     ​20 ​       0    0    0     N
 +
 +  13  2472b     ​20 ​       0    0    0     N
 +
 +wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
 +
 +wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
 +
 +wifi0: mac 7.8 phy 4.5 radio 5.6
 +
 +wifi0: Use hw queue 1 for WME_AC_BE traffic
 +
 +wifi0: Use hw queue 0 for WME_AC_BK traffic
 +
 +wifi0: Use hw queue 2 for WME_AC_VI traffic
 +
 +wifi0: Use hw queue 3 for WME_AC_VO traffic
 +
 +wifi0: Use hw queue 8 for CAB traffic
 +
 +wifi0: Use hw queue 9 for beacons
 +
 +wifi0: Use hw queue 7 for UAPSD
 +
 +wifi0: Atheros 5212: mem=0x10000000,​ irq=39 hw_base=0xb0000000
 +
 +wlan: mac acl policy registered
 +
 +wl0
 +wl1
 +Starting Switch...
 +    switch.ko... Switch module creating proc entry
 +
 +ok
 +*********************** Starting script /​etc/​rc1.d/​S15syslogd at: 37.37 0.92
 +*********************** Starting script /​etc/​rc1.d/​S16voice1 at: 37.88 0.92
 +Voice part 1 start ...
 +krtp ver 2.8 softdsp-vad-multiline-wb (Jun  8 2009 20:25:28)
 +
 +USB DECT Upper driver installed
 +
 +*********************** Starting script /​etc/​rc1.d/​S20network at: 41.58 0.92
 +Local network configuration ...
 +Ethernet network configuration ...
 +Hostname configuration : LIVEBOX
 +*********************** Starting script /​etc/​rc1.d/​S22gatewayd at: 44.06 0.92
 +[Lua] ######################################################​
 +
 +[Lua] Converting for port AutoConfig feature
 +
 +[Lua] ######################################################​
 +
 +loading geniodb kernel modules...
 + ​Thomson geniodb driver: Loading ...
 +
 + ​Thomson geniodb driver: Loading finished with SUCCESS
 +
 +gatewayd start ...
 +get rescue hco version failed
 +
 +wait until stage >= 71 (current stage=22)
 +
 +wait until stage >= 71 (current stage=22)
 +
 +Lock created on /​var/​run/​mbusd_system pid:1026
 +
 +Lock created on /​var/​run/​mbusd pid:1027
 +
 +Lock created on /​var/​run/​mbusd_atomic pid:1027
 +
 +[ADSL PLUGIN] Plugin '​DSL_MBUS'​ Plugin successfully registerd !
 +
 +[ADSL PLUGIN] Plugin '​DSL_MBUS'​ Successfully registered !
 +
 +[ADSL PLUGIN] Plugin '​DSL_MBUS'​ ADSL API device char successfully open!
 +
 +[ADSL PLUGIN] Plugin '​DSL_MBUS'​ Successfully registered !
 +
 +wait until stage >= 71 (current stage=22)
 +
 +wait for gatewayd to initialise (1)
 +wait until stage >= 71 (current stage=22)
 +
 +wait until stage >= 99 (current stage=22)
 +
 +wait until stage >= 71 (current stage=22)
 +
 +End of initialisation
 +
 +wait until stage >= 60 (current stage=22)
 +
 +*********************** Starting script /​etc/​rc1.d/​S23qos at: 57.53 1.22
 +wait until stage >= 71 (current stage=23)
 +
 +wait until stage >= 99 (current stage=23)
 +
 +wait until stage >= 71 (current stage=23)
 +
 +wait until stage >= 60 (current stage=23)
 +
 +wait until stage >= 71 (current stage=23)
 +
 +wait until stage >= 71 (current stage=23)
 +
 +wait until stage >= 99 (current stage=23)
 +
 +wait until stage >= 60 (current stage=23)
 +
 +wait until stage >= 71 (current stage=23)
 +
 +wait until stage >= 71 (current stage=23)
 +
 +wait until stage >= 99 (current stage=23)
 +
 +wait until stage >= 60 (current stage=23)
 +
 +wait until stage >= 71 (current stage=23)
 +
 +wait until stage >= 71 (current stage=23)
 +
 +wait until stage >= 99 (current stage=23)
 +
 +wait until stage >= 60 (current stage=23)
 +
 +*********************** Starting script /​etc/​rc1.d/​S24resolvd at: 61.35 1.22
 +Resolv daemon start ...
 +wait until stage >= 71 (current stage=24)
 +
 +wait until stage >= 71 (current stage=24)
 +
 +wait until stage >= 99 (current stage=24)
 +
 +wait until stage >= 60 (current stage=24)
 +
 +*********************** Starting script /​etc/​rc1.d/​S40nlplugd at: 62.32 1.22
 +wait until stage >= 71 (current stage=40)
 +
 +wait until stage >= 71 (current stage=40)
 +
 +wait until stage >= 99 (current stage=40)
 +
 +nlplugd start ...
 +wait until stage >= 60 (current stage=40)
 +
 +Initializing.
 +
 +Lock file '/​var/​run/​mbusd_atomic'​ exists and is locked.
 +
 +Starting netlink plugin
 +
 +Lock created on /​var/​run/​NL_PLUGIN_MBUS pid:1204
 +
 +Daemonize netlink plugin
 +
 +
 +
 +wait until stage >= 71 (current stage=40)
 +
 +*********************** Starting script /​etc/​rc1.d/​S41iptplugd at: 63.48 1.22
 +iptplugd start ...
 +Lock created on /​var/​run/​IPT_PLUGIN_MBUS pid:1223
 +
 +Daemonize iptables plugin
 +
 +
 +
 +wait until stage >= 71 (current stage=41)
 +
 +wait until stage >= 71 (current stage=41)
 +
 +wait until stage >= 99 (current stage=41)
 +
 +wait until stage >= 60 (current stage=41)
 +
 +Lock created on /​var/​run/​NL_PLUGIN_MBUS pid:1206
 +
 +*********************** Starting script /​etc/​rc1.d/​S42mbus_wland at: 64.20 1.22
 +wait until stage >= 71 (current stage=42)
 +
 +MBUS start: ath_wland
 +Lock created on /​var/​run/​WLAN pid:1239
 +
 +Lock created on /​var/​run/​IPT_PLUGIN_MBUS pid:1225
 +
 +wait until stage >= 71 (current stage=45)
 +
 +wait until stage >= 71 (current stage=45)
 +
 +wait until stage >= 99 (current stage=45)
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +wait until stage >= 60 (current stage=45)
 +
 +*********************** Starting script /​etc/​rc1.d/​S45checkd at: 64.98 1.22
 +checkd start ...
 +checkd: daemonized with blocked parent process
 +
 +ath_chan_set:​ Changing to channel 2417, Flags c0, PF 0
 +
 +wait until stage >= 71 (current stage=45)
 +
 +checkd: parent process released.
 +checkd: running
 +ath_chan_set:​ Changing to channel 2422, Flags c0, PF 0
 +
 +*********************** Starting script /​etc/​rc1.d/​S45dhccd at: 65.57 1.22
 +dhccd start ...
 +ath_chan_set:​ Changing to channel 2427, Flags c0, PF 0
 +
 +wait until stage >= 71 (current stage=45)
 +
 +wait until stage >= 71 (current stage=45)
 +
 +wait until stage >= 99 (current stage=45)
 +
 +wait until stage >= 60 (current stage=45)
 +
 +ath_chan_set:​ Changing to channel 2432, Flags c0, PF 0
 +
 +*********************** Starting script /​etc/​rc1.d/​S47igmpsnoopd at: 66.23 1.22
 +wait until stage >= 71 (current stage=47)
 +
 +Igmp Snooping start ...
 +ath_chan_set:​ Changing to channel 2437, Flags c0, PF 0
 +
 +ath_chan_set:​ Changing to channel 2442, Flags c0, PF 0
 +
 +wait until stage >= 71 (current stage=47)
 +
 +wait until stage >= 71 (current stage=47)
 +
 +wait until stage >= 99 (current stage=47)
 +
 +wait until stage >= 60 (current stage=47)
 +
 +ath_chan_set:​ Changing to channel 2447, Flags c0, PF 0
 +
 +ath_chan_set:​ Changing to channel 2452, Flags c0, PF 0
 +
 +wait until stage >= 71 (current stage=ath_chan_set:​ Changing to channel 2457, Flags c0, PF 0
 +
 +47)
 +
 +wait until stage >= 71 (current stage=50)
 +
 +wait until stage >= 71 (current stage=50)
 +
 +wait until stage >= 99 (current stage=50)
 +
 +ath_chan_set:​ Changing to channel 2462, Flags c0, PF 0
 +
 +wait until stage >= 60 (current stage=50)
 +
 +*********************** Starting script /​etc/​rc1.d/​S50dhcspd at: 67.98 1.22
 +dhcspd start ...
 +dhcspd: Daemonized with blocked parent process
 +
 +ath_chan_set:​ Changing to channel 2467, Flags c0, PF 0
 +
 +ath_chan_set:​ Changing to channel 2472, Flags c0, PF 0
 +
 +dhcspd: Parent process released.
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ath_chan_set:​ Changing to channel 2412, Flags c0, PF 0
 +
 +wait until stage >= 71 (current stage=50)
 +
 +wait until stage >= 71 (current stage=50)
 +
 +wait until stage >= 71 (current stage=50)
 +
 +wait until stage >= 99 (current stage=50)
 +
 +wait until stage >= 60 (current stage=51)
 +
 +*********************** Starting script /​etc/​rc1.d/​S51cached at: 69.03 1.22
 +dhcp cache daemon start ...
 +cached: Daemonized with blocked parent process
 +
 +wait until stage >= 71 (current stage=51)
 +
 +cached: Parent process released.
 +wait until stage >= 71 (current stage=51)
 +
 +wait until stage >= 71 (current stage=51)
 +
 +wait until stage >= 99 (current stage=51)
 +
 +wait until stage >= 60 (current stage=51)
 +
 +*********************** Starting script /​etc/​rc1.d/​S650atomicstopload at: 70.10 1.22
 +wait until configuration load reaches phase 5 (now -1, 1s)
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +stage 60 reached (current stage=65)
 +
 +appbox: start loading after [ 14089ms ]
 +
 +stage 60 reached (current stage=65)
 +
 +stage 61 reached (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +stage 62 reached (current stage=65)
 +
 +stage 63 reached (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +stage 64 reached (current stage=65)
 +
 +_MODEMLABEL= bcm96358_ADSL_PHY_A2pBT010g2.d20h
 +
 +_ADSL_EOC_VERSION= ff81637.2.9.8
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ath_chan_set:​ Changing to channel 2437, Flags c0, PF 0
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ath_chan_set:​ Changing to channel 2412, Flags c0, PF 0
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ni->​ni_vap->​iv_opmode = 6
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +device eth0 entered promiscuous mode
 +
 +bridge: port 1(eth0) entering learning state
 +
 +bridge: topology change detected, propagating
 +
 +bridge: port 1(eth0) entering forwarding state
 +
 +device wl0 entered promiscuous mode
 +
 +bridge: port 2(wl0) entering learning state
 +
 +bridge: topology change detected, propagating
 +
 +bridge: port 2(wl0) entering forwarding state
 +
 +wait until stage >= 71 (current stage=65)
 +
 +device eth1 entered promiscuous mode
 +
 +bridge: port 3(eth1) entering learning state
 +
 +bridge: topology change detected, propagating
 +
 +bridge: port 3(eth1) entering forwarding state
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +stage 65 reached (current stage=65)
 +
 +wait until stage >= 66 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +Configuration file: /​tmp/​hostapd.conf.0
 +ni->​ni_vap->​iv_opmode = 6
 +
 +bridge: port 2(wl0) entering disabled state
 +
 +Using interface wl0 with hwaddr 00:​18:​e7:​31:​2c:​ef and ssid '​Livebox-9948'​
 +wait until stage >= 66 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wl0: RADIUS Authentication server 127.0.0.1:​1812
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +ath_newstate:​ Resetting VAP dfswait_run
 +
 +bridge: port 2(wl0) entering learning state
 +
 +bridge: topology change detected, propagating
 +
 +bridge: port 2(wl0) entering forwarding state
 +
 + ​key_alloc_2pair:​ sc_splitmic SET to 1
 +
 +Flushing old station entries
 +Deauthenticate all stations
 +l2_packet_receive - recvfrom: Network is down
 +l2_packet_receive - recvfrom: Network is down
 +*********************** Starting script /​etc/​rc1.d/​S651usb-host at: 92.03 1.66
 +wait until stage >= 66 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +usbmgr[1586]:​ start 0.4.8
 +usbmgr[1586]:​ sleep time -1 micro sec
 +
 +Name: /​etc/​usbmgr/​usbmgr.conf
 +wait until stage >= 66 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +Load_from_file:​ /​etc/​usbmgr/​preload.conf
 +usbmgr[1600]:​ [USB_MBUS]Plugin '​USB_MBUS'​ successfully registered!
 +
 +
 +wait until stage >= 66 (current stage=65)
 +
 +*********************** Starting script /​etc/​rc1.d/​S65audiphone_plugin at: 94.63 1.66
 +usbmgr[1600]:​ [USB_MBUS]succeed to create listening thread
 +
 +
 +Lock created on /​var/​run/​USB_MBUS pid:1622
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +usbmgr[1600]:​ buffer line: remove T
 +wait until stage >= 66 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +usbmgr[1600]:​ class:0x9 subclass:​0x0 protocol:​0x0
 +usbmgr[1600]:​ try /​etc/​usbmgr/​class/​09/​00/​00/​module
 +usbmgr[1600]:​ try /​etc/​usbmgr/​class/​09/​00/​module
 +usbmgr[1600]:​ try /​etc/​usbmgr/​class/​09/​module
 +wait until stage >= 71 (current stage=65)
 +
 +usbmgr[1600]:​ try /​etc/​usbmgr/​class/​module
 +usbmgr[1600]:​ USB device isn't matched the configuration
 +wait until stage >= 99 (current stage=65)
 +
 +usbmgr[1600]:​ buffer line: remove T
 +wait until stage >= 71 (current stage=65)
 +
 +Starting audiphone_plugin
 +wait until stage >= 66 (current stage=65)
 +
 +audiphone plugin : Finished (no error).
 +*********************** Starting script /​etc/​rc1.d/​S65devdiscd at: 96.98 1.66
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +Device Discovery start ...
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +devdiscd: Daemonized with blocked parent process
 +
 +wait until stage >= 66 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +devdiscd: Parent process released.
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +*********************** Starting script /​etc/​rc1.d/​S65ezpFTplugin at: 98.34 1.66
 +Starting EasyPairingPlugin
 +Initializing.
 +Registering metadata to mbusd.
 +wait until stage >= 66 (current stage=65)
 +
 +Finished (no error).
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +*********************** Starting script /​etc/​rc1.d/​S65network2 at: 99.07 1.66
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +Ethernet network configuration ...
 +wait until stage >= 66 (current stage=65)
 +
 +*********************** Starting script /​etc/​rc1.d/​S65todd at: 99.66 1.66
 +Timeofday start ...
 +[TOD MAIN] Initializing application.
 +
 +[TOD MAIN] Initialization application successful.
 +
 +[TOD MAIN] daemonizing..
 +
 +[TOD MAIN] Initializing daemon.
 +
 +Lock file '/​var/​run/​mbusd_atomic'​ exists and is locked.
 +
 +Lock file '/​var/​run/​mbusd_atomic'​ exists and is locked.
 +
 +Lock created on /​var/​run/​tod_plugin pid:1712
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +[TOD MAIN] Initializing daemon done.
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +wait until stage >= 99 (current stage=65)
 +
 +wait until stage >= 71 (current stage=65)
 +
 +*********************** Starting script /​etc/​rc1.d/​S70stopload at: 100.34 1.66
 +stage 66 reached (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +stage 67 reached (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +stage 68 reached (current stage=70)
 +
 +stage 70 reached (current stage=70)
 +
 +Upnp init ...
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +route: SIOC[ADD|DEL]RT:​ File exists
 +Stopping application:​ audiphone4BLB
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +appbox: end loading
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +killall: audiphone4BLB:​ no process killed
 +MyConfig in /​etc/​upnp.conf:​
 + Debug=0
 + descDocName:​ gatedesc.xml
 + xmlPath: /var
 + g_iptables:​ /​usr/​sbin/​iptables
 + g_forwardChainName:​ upnp
 + g_preroutingChainName:​ upnp
 + g_upstreamBitrate:​ 0
 + g_downstreamBitrate:​ 0
 +
 +retrieving the address
 +creating a socket
 +performing the SIOCGIFADDR ioctl
 +found ifaddr '​192.168.1.1'​ for bridge
 +creating pid file
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +Lock created on /​var/​run/​UPnP pid:1759
 +
 + INFO : IGD root device successfully registered.
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +device atm_1 entered promiscuous mode
 +
 +bridge_0: port 1(atm_1) entering learning state
 +
 +bridge_0: topology change detected, propagating
 +
 +bridge_0: port 1(atm_1) entering forwarding state
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +eth0: received packet with  own address as source address
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +device atm_2 entered promiscuous mode
 +
 +bridge_0: port 2(atm_2) entering learning state
 +
 +bridge_0: topology change detected, propagating
 +
 +bridge_0: port 2(atm_2) entering forwarding state
 +
 +eth0: received packet with  own address as source address
 +
 +eth0: received packet with  own address as source address
 +
 +eth0: received packet with  own address as source address
 +
 +device atm_3 entered promiscuous mode
 +
 +bridge_0: port 3(atm_3) entering learning state
 +
 +bridge_0: topology change detected, propagating
 +
 +bridge_0: port 3(atm_3) entering forwarding state
 +
 +eth0: received packet with  own address as source address
 +
 +eth0: received packet with  own address as source address
 +
 +eth0: received packet with  own address as source address
 +
 +eth0: received packet with  own address as source address
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +device atm_4 entered promiscuous mode
 +
 +bridge_0: port 4(atm_4) entering learning state
 +
 +bridge_0: topology change detected, propagating
 +
 +bridge_0: port 4(atm_4) entering forwarding state
 +
 +eth0: received packet with  own address as source address
 +
 +eth0: received packet with  own address as source address
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +device eth1 left promiscuous mode
 +
 +bridge: port 3(eth1) entering disabled state
 +
 + INFO : Advertisements Sent.  Listening for requests ... 
 +device eth1 entered promiscuous mode
 +
 +bridge_0: port 5(eth1) entering learning state
 +
 +bridge_0: topology change detected, propagating
 +
 +bridge_0: port 5(eth1) entering forwarding state
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +>= 71 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +device eth1 left promiscuous mode
 +
 +bridge_0: port 5(eth1) entering disabled state
 +
 +device eth1 entered promiscuous mode
 +
 +bridge: port 3(eth1) entering learning state
 +
 +bridge: topology change detected, propagating
 +
 +bridge: port 3(eth1) entering forwarding state
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 71 (current stage=wait until stage >= 71 (current stage=70)
 +
 +70)
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 99 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +wait until stage >= 71 (current stage=70)
 +
 +stage 71 reached (current stage=72)
 +
 +wait until stage >= 99 (current stage=72)
 +
 +stage 71 reached (current stage=72)
 +
 +stage 71 reached (current stage=72)
 +
 +stage 71 reached (current stage=72)
 +
 +stage 71 reached (current stage=72)
 +
 +Lock created on /​var/​run/​qosd_igd_client pid:1152
 +
 +*********************** Starting script /​etc/​rc1.d/​S72hostmgr at: 118.33 1.66
 +hostmgr start ...
 +Lock created on /​var/​run/​Hostmanager pid:1805
 +
 +*********************** Starting script /​etc/​rc1.d/​S75appweb at: 118.86 1.66
 +wait until stage >= 99 (current stage=75)
 +
 +Lock created on /​var/​run/​qosd_atomic_client pid:1152
 +
 +gio_if_idx2nam:​ ioctl(SIOCGIFNAME) fails with: No such device
 +
 +wait until stage >= 99 (current stage=75)
 +
 +wait until stage >= 99 (current stage=75)
 +
 +wait until stage >= 99 (current stage=75)
 +
 +Starting appWeb
 +wait until stage >= 99 (current stage=75)
 +
 +*********************** Starting script /​etc/​rc1.d/​S76dslupd at: 123.82 1.66
 +wait until stage >= 99 (current stage=76)
 +
 +Dslupdate start ...
 +Lock created on /​var/​run/​ATMQOS pid:1873
 +
 +wait until stage >= 99 (current stage=76)
 +
 +*********************** Starting script /​etc/​rc1.d/​S77tppp at: 125.17 1.66
 +wait until stage >= 99 (current stage=77)
 +
 +tppp start ...
 +Lock created on /​var/​run/​TPPP pid:1893
 +
 +Lock created on /​var/​run/​TPPP_IGD pid:1893
 +
 +*********************** Starting script /​etc/​rc1.d/​S80telnetd at: 126.96 1.66
 +wait until stage >= 99 (current stage=80)
 +
 +telnetd start ...
 +*********************** Starting script /​etc/​rc1.d/​S81ezp_ctl at: 127.72 1.66
 +EasyPairing Management Deamon start: ezpairingctl
 +wait until stage >= 99 (current stage=80)
 +
 +*********************** Starting script /​etc/​rc1.d/​S98pwrledstop at: 128.21 1.66
 +pwrledstart stop ...
 +Lock created on /​var/​run/​ezp_atom pid:1916
 +
 +Lock created on /​var/​run/​ezp_igd pid:1916
 +
 +wl0 enabled
 +wait until stage >= 99 (current stage=98)
 +
 +*********************** Starting script /​etc/​rc1.d/​S98voice2 at: 129.47 1.66
 +Voice part 2 start ...
 +wait until stage >= 99 (current stage=98)
 +
 +load dspdd.ko: core_size=874992,​ init_size=0
 +
 +DSP Driver: DSP init stub
 +
 +wait until stage >= 99 (current stage=98)
 +
 +Endpoint: endpoint_init entry
 +
 +BOS: Enter bosInit ​
 +
 +Enter bosAppInit ​
 +
 +Exit bosAppInit ​
 +
 +BOS: Exit bosInit ​
 +
 +Endpoint: endpoint_init COMPLETED
 +
 +wait until stage >= 99 (current stage=98)
 +
 +kernel::​endpoint_open
 +
 +kernel::​endpoint_open COMPLETED
 +
 +Enter bosStartApp
 +
 +
 +
 +bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...
 +
 +
 +
 +
 +bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...
 +
 +
 +Enter TaskCreate aoAP
 +
 +TaskCreate - spawn new task aoAP
 +
 +Exit bosStartApp
 +
 +Exit TaskCreate ​
 +
 +AppResetDetectionEnable() - Enabled reset detection.
 +
 +Setting path=Voice, param=StartDriver,​ value=1 successfully!
 +PLL init completed. PLL registers set to:
 +
 +PCM->​pcm_pll_ctrl1 ​      = 0x00020001 ​
 +
 +PCM->​pcm_pll_ctrl2 ​      = 0x0008492B ​
 +
 +PCM->​pcm_pll_ctrl3 ​      = 0x00001E1C ​
 +
 +Set up PCM registers
 +
 +Channel 0 assigned to timeslot 0
 +
 +Channel 1 assigned to timeslot 1
 +
 +Channel 2 assigned to timeslot 2
 +
 +Tx Desc (0xA146E000):​ chan 0, buf 0, sts 0xe000, len 1280, bufp 0x1424000 ​
 +
 +Tx Desc (0xA146E008):​ chan 0, buf 1, sts 0x7000, len 1280, bufp 0x1424510 ​
 +
 +Rx Desc (0xA14AC000):​ chan 0, buf 0, sts 0x8000, len 1280, bufp 0x3938000 ​
 +
 +Rx Desc (0xA14AC008):​ chan 0, buf 1, sts 0x9000, len 1280, bufp 0x3938510 ​
 +
 +initIudma: chan 0, descBase 0xa14ac000, descBaseIudma 0x14ac000
 +
 +initIudma: chan 1, descBase 0xa146e000, descBaseIudma 0x146e000
 +
 +PCM ENABLE INFO: DMA0 IRQ STATUS 0x00000000
 +
 +PCM ENABLE INFO: DMA0 IRQ MASK   ​0x00000005
 +
 +PCM ENABLE INFO: DMA1 IRQ STATUS 0x00000000
 +
 +PCM ENABLE INFO: DMA1 IRQ MASK   ​0x00000005
 +
 +PCM ENABLE INFO: PCM  IRQ MASK    0x00000003
 +
 +PCM ENABLE INFO: PCM  IRQ PENDING 0x00000007
 +
 +Enter TaskCreate CMT_EXCEPTION_IST
 +
 +TaskCreate - spawn new task CMT_EXCEPTION_IST
 +
 +Exit TaskCreate ​
 +
 +regStatus (reg 12 sel 0)    = 0x10008701 ​
 +
 +regStatus (reg 12 sel 7)    = 0x00000101 ​
 +
 +regCause ​ (reg 13 sel 0)    = 0x00000008 ​
 +
 +regCause ​ (reg 13 sel 7)    = 0x00808000 ​
 +
 +regCMT ​   (reg 22 sel 0)    = 0xe30e1006 ​
 +
 +regCMT ​   (reg 22 sel 1)    = 0x10008001 ​
 +
 +regCMT ​   (reg 22 sel 2)    = 0x00020020 ​
 +
 +regCMT ​   (reg 22 sel 3)    = 0x00000003 ​
 +
 +regCMT ​   (reg 22 sel 4)    = 0x00000000 ​
 +
 +regCMT ​   (reg 22 sel 5)    = 0x00000020 ​
 +
 +Kicking off secondary thread processor at entry point 0x8108A6A0...
 +
 +Secondary thread processor entry point at 0x8108a6a0
 +
 +wait until stage >= 99 (current stage=98)
 +
 +Thread processor handshake. Secondary app initialized properly.
 +
 +IPC Shared mem at 811452a0, size 106504 (max 110000)
 +
 +SUCCESS: Took semaphore
 +
 +SUCCESS: Gave semaphore
 +
 +INFO: MSPI POLLING MODE
 +
 +INFO: IRQ MASK 0xa0028624
 +
 +INFO: IRQ STATUS 0x400001
 +
 +INFO: BLOCK ENABLES 0x3e0320
 +
 +MSPI INITIALIZED
 +
 +boardHalSlicSi3215Init:​ Slic 1 usGpioSlicReset not set
 +
 +boardHalSlicSi3215Init:​ Slic 0 usGpioSlicRelay not set
 +
 +boardHalSlicSi3215Init:​ Slic 1 usGpioSlicRelay not set
 +
 +slicConfigure() reading 3 from slic 0 devId 2
 +
 +Read Si3215 Revision H on slic 0
 +
 +Direct read/write test passed on slic 0
 +
 +Indirect read/write test passed on slic 0
 +
 +Entering SLIC DC Power Calibration check ......Passed
 +
 +Entering SLIC Calibration check................Passed
 +
 +Entering Manual Calibration check................stage 99 reached (current stage=99)
 +
 +Passed 1 ... *********************** Starting script /​etc/​rc1.d/​S99printkoff at: 134.15 1.66
 +Setting printk off
 +*** gStartRxDesc[0] = 0xA14AC000 ​
 +*** gBufferSizeBytes = 1280 
 +*** gStartTxDesc[0] = 0xA146E000 ​
 +hal6358PcmInit 260 nextTxDesc = 0xA146E000 ​
 +hal6358PcmInit 260 nextTxDesc = 0xA146E008 ​
 +hal6358PcmInit 264 Ownership for TX desc not set. Use this buffer. ​
 +PERF->​IrqMask ​  = 0xA0028624 ​
 +PERF->​IrqMask1 ​ = 0x00800000 ​
 +Next bootmode set to : system (ok)
 +Sysinit done.
 +
 +Please press Enter to activate this console. ​
 +LIVEBOX login: root
 +Password: ​
 +/​mnt/​jffs2/​jffs2_3/​system/​root # 
 +/​mnt/​jffs2/​jffs2_3/​system/​root # 
 +/​mnt/​jffs2/​jffs2_3/​system/​root # 
 +/​mnt/​jffs2/​jffs2_3/​system/​root # 
 +/​mnt/​jffs2/​jffs2_3/​system/​root # 
 +/​mnt/​jffs2/​jffs2_3/​system/​root #  :0)
 +</​code>​
livebox_thomson_bootlog.txt · Dernière modification: 2015/01/28 03:09 (modification externe)